Sixty documented references for doors, gates, machines and industrial equipment. SENTIR edge 65 ST is presented first; components are selected for the project and applicable manuals.
35 × 65 mm TPE pressure-sensitive profile with side-clip feet, contributing to contact detection on a closure or moving part. Assembly combines suitable end caps, connections and mounting rail, with evaluation electronics defined for the installation.
35 × 65 mm profile. Specify finished length, rail, connections and electronics in the quotation.
The profile is a component of a pressure-sensitive assembly: category and performance level depend on the complete chain, chosen electronics and installation conditions. Finished length, accessories and wiring are defined in the quotation. Force and travel curves correspond to manufacturer test conditions; electronic response time affects sizing. The current ASO datasheet gives 35 × 65 mm and IP67; archives mention 36 mm or IP65, which must be distinguished from the current configuration.
Official ASO data and instructions ↗This selection follows functions described in ASO manuals. It distinguishes internally monitored relays from references whose testing depends on the higher-level controller.
Single-channel DIN-rail relay for an 8.2 kΩ tactile device, with redundant output and fault diagnostics. Validate its configuration and safety chain for the installation.
View the product page →ASO manual · p. 16
Two monitored 8.2 kΩ tactile circuits with mutually monitoring safety relays. 24 V AC/DC supply and DIN-rail mounting; outputs are restricted to extra-low voltage.
View the product page →ASO manual · p. 15
Dual-channel enclosed relay for two 8.2 kΩ tactile circuits. Its manual describes a redundant, mutually monitoring architecture; connection and final protection follow the installation requirements.
View the product page →ASO manual · p. 15
For one 8.2 kΩ tactile device, with redundant output and fault diagnostics in a wall-mounted enclosure. Validate the reset functions and complete installation against the manual.
View the product page →ASO manual · p. 1
Two monitored tactile circuits and redundant safety outputs, for an 85–265 V AC or 24 V AC/DC supply. The manual distinguishes the relay ratings from those of the system with sensors.
View the product page →ASO manual · p. 22Module ratings are not ratings for the complete door or gate. Validate wiring, interfaces and tests for the installation.
Understand testing and the 2027 transition →35 × 65 mm TPE pressure-sensitive profile with side-clip feet, contributing to contact detection on a closure or moving part. Assembly combines suitable end caps, connections and mounting rail, with evaluation electronics defined for the installation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR contact-sensitive profile with side clips, 35 mm wide and 45 mm high, for contact detection at pinch and shear points. ASO offers it as a profile for assembly, a kit or a preassembled product. Length, rail, end components and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR contact-sensitive profile with side clips, 36 mm wide and 85 mm high, for contact detection at pinch and shear points. ASO offers it as a profile for assembly, a kit or a preassembled product. Length, rail, end components and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR pressure-sensitive profile with T-shaped foot, 15 mm wide and 23,5 mm high, for contact detection at crushing and shearing points. ASO offers it as a profile for assembly, a kit or a preassembled unit. Length, mounting rail, end terminations and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR pressure-sensitive profile with T-shaped foot, 25 mm wide and 30 mm high, for contact detection at crushing and shearing points. ASO offers it as a profile for assembly, a kit or a preassembled unit. Length, mounting rail, end terminations and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR pressure-sensitive profile with T-shaped foot, 35 mm wide and 55 mm high, for contact detection at crushing and shearing points. ASO offers it as a profile for assembly, a kit or a preassembled unit. Length, mounting rail, end terminations and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR pressure-sensitive profile with T-shaped foot, 35 mm wide and 85 mm high, for contact detection at crushing and shearing points. ASO offers it as a profile for assembly, a kit or a preassembled unit. Length, mounting rail, end terminations and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR contact-sensitive profile with side clips, 45 mm wide and 115 mm high, for contact detection at pinch and shear points. ASO offers it as a profile for assembly, a kit or a preassembled product. Length, rail, end components and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR pressure-sensitive profile with T-shaped foot, 8 mm wide and 8 mm high, for contact detection at crushing and shearing points. ASO offers it as a profile for assembly, a kit or a preassembled unit. Length, mounting rail, end terminations and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
SENTIR contact-sensitive profile for round posts, 92 mm wide and 67,5 mm high, for contact detection at pinch and shear points. ASO offers it as a profile for assembly, a kit or a preassembled product. Length, rail, end components and monitoring electronics are specified in the quotation.
Original manufacturer: ASO Safety Solutions.
View the product page →
A compact 15.5 × 9 mm contact profile with a T-foot for installations with limited space. It fits the AL 15-9 mounting rail and requires suitable evaluation electronics.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 15 × 23.5 mm T-foot variant described by ASO as oil-resistant. This tactile contact profile fits the AL 15-9 aluminium rail.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 25 × 40 mm NBR hollow-chamber profile for building an installation-specific contact edge. ASO lists several AL 25 aluminium rails for mounting.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 25 × 30 mm T-foot contact profile in the flame-retardant TB version. ASO lists DIN 4102 B1 and ECE R118, appendices 7 and 8, for this variant.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 25 × 45 mm T-foot safety contact edge for tactile detection on moving equipment. It is mounted using a suitable AL 25 aluminium retaining rail.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 30 × 70 mm T-foot contact profile used with the AL 30-14 aluminium rail. Selection should account for available space, mounting and evaluation of the assembled edge.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 35 × 60 mm NBR hollow-chamber profile for contact-edge assemblies. ASO lists several AL 35 rail designs to suit different mounting arrangements.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 35 × 55 mm safety contact edge with a clamping fin. Its mounting geometry differs from the T-foot model and must be matched to the intended support.
Original manufacturer: ASO Safety Solutions.
View the product page →
A 35 × 45 mm contact profile with a double T-foot. It offers a different mounting geometry from the side-clipped 45 ST; ASO specifies aluminium rails on request.
Original manufacturer: ASO Safety Solutions.
View the product page →
A contact-edge profile for corner posts, measuring 96.5 × 70.7 mm according to ASO. Its shape suits this support arrangement; delivery length is specified on request.
Original manufacturer: ASO Safety Solutions.
View the product page →
Single-channel monitoring relay in a surface-mount housing. It evaluates a pressure-sensitive sensor with 8,2 kΩ termination and has one relay contact. ASO publishes a 230 V or 24 V AC/DC supply; choose the connection and test according to the instructions.
Original manufacturer: ASO Safety Solutions.
View the product page →Two-channel monitoring relay for DIN-rail mounting and 24 V AC/DC power. It evaluates two sensor inputs with 8,2 kΩ termination and has redundant force-guided contacts. Validate sensor and controller connections according to the ASO manual.
Original manufacturer: ASO Safety Solutions.
View the product page →
Two-channel DIN-rail monitoring device, with two 8,2 kΩ sensor inputs and two relay contacts. It is offered with 230 V or 24 V AC/DC power. Sensor, test logic and wiring selection depends on the application.
Original manufacturer: ASO Safety Solutions.
View the product page →Single-channel DIN rail monitoring relay for evaluating a contact sensor with 8,2 kΩ termination. It has a redundant force-guided contact. Select supply and test functions according to the instructions and the installation's control architecture.
Original manufacturer: ASO Safety Solutions.
View the product page →
Inductive transmission set for moving safety edges on sliding gates, with 8,2 kΩ termination monitoring. It includes the DIN-rail unit, fixed and moving cores, a 20 m sheathed steel cable and tensioning device. Unit power supply: 24 V AC/DC.
Original manufacturer: ASO Safety Solutions.
View the product page →
Inductive transmission assembly for moving safety edges, with surface-mount housing unit, fixed and moving cores, 20 m coated steel cable and tensioning device. Transmission is battery-free; the unit is powered by 230 V or 24 V AC/DC depending on the connection.
Original manufacturer: ASO Safety Solutions.
View the product page →
Configurable contact mat assembly for monitoring a machine work area. Pressure on the mat triggers a signal to be processed by suitable safety electronics. ASO states polyurethane covering and a 24 V, 100 mA circuit; dimensions and assembly to be defined.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO pressure-sensitive bumper for outdoor use and ground support equipment (GSE). It combines a deformable volume with a detection contact for areas requiring a longer compression stroke. Dimensions, force, mounting and electronics must suit the movement being monitored.
Original manufacturer: ASO Safety Solutions.
View the product page →
Radar assembly for barriers comprising a sensor and an evaluation unit. It detects objects and vehicles within a configurable field to control passage. The data sheet states a 13 m detection distance; placement, settings, software and connection depend on the site.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO control for sliding gate, shutter and sectional door drives, described for 400 V three-phase and 230 V single-phase motors. It forms part of a defined control and safety architecture. Check motor type, limit switches and sensors before selection.
Original manufacturer: ASO Safety Solutions.
View the product page →
Single-channel DIN-rail module for reading a tactile device with an 8.2 kΩ terminal resistance and providing a relay contact. ASO explicitly states that this model is not intended for safety systems.
Original manufacturer: ASO Safety Solutions.
View the product page →Dual-channel evaluation relay in a wall-mounted enclosure for two 8.2 kΩ tactile signal transmitters. Two redundant forcibly guided relay outputs pass their states to a machine or gate controller.
Original manufacturer: ASO Safety Solutions.
View the product page →
DIN-rail relay that evaluates two 8.2 kΩ signal transmitters and provides one common relay contact. It integrates with a controller that performs the ASO test required for the category 2 architecture.
Original manufacturer: ASO Safety Solutions.
View the product page →
24 V DC dual-channel DIN-rail evaluation module for two 8.2 kΩ signal transmitters. Its two semiconductor outputs connect to a controller compatible with this interface.
Original manufacturer: ASO Safety Solutions.
View the product page →Single-channel evaluation relay in a wall-mounted enclosure for one 8.2 kΩ tactile signal transmitter. It provides a redundant forcibly guided relay output, with published supply options of 230 V AC or 24 V AC/DC.
Original manufacturer: ASO Safety Solutions.
View the product page →Dual-channel DIN-rail evaluation relay for two 8.2 kΩ signal transmitters, with two redundant forcibly guided relay contacts. It accepts an 85–265 V AC mains supply or a 24 V AC/DC supply.
Original manufacturer: ASO Safety Solutions.
View the product page →
Battery-free transmission set between a moving 8.2 kΩ contact edge and the fixed controller of a sliding gate. The ASO page lists the version R module with test input and display, moving SPK 54 S coil core and cable mounting assembly.
Original manufacturer: ASO Safety Solutions.
View the product page →
Evaluation board for the ELMON inductive signal transmission system, manufacturer model 70-755, article 1203-0020. This unenclosed version is listed for 24 V DC supply and must be selected together with the other system components and interfaces.
Original manufacturer: ASO Safety Solutions.
View the product page →
Evaluation board for the ELMON inductive signal transmission system, manufacturer model 70-757, article 1402-0740. This unenclosed version is listed for 24 V DC supply and must be selected together with the other system components and interfaces.
Original manufacturer: ASO Safety Solutions.
View the product page →
Evaluation board for the ELMON inductive signal transmission system, manufacturer model 74-332, article 1206-0070. This unenclosed version is listed for 24 V AC/DC or 230 V AC ±10% supply and must be selected together with the other system components and interfaces.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO frequency converter controller for doors and gates, in FU A0101 version. Its three-phase 230 V motor output is rated at 4 A. A display and selection controls support setup and diagnostics, with inputs for command devices, limit switches and detection equipment.
Original manufacturer: ASO Safety Solutions.
View the product page →ASO frequency converter controller for doors and gates, in FU A0102 version. Its three-phase 230 V motor output is rated at 10 A. A display and selection controls support setup and diagnostics, with inputs for command devices, limit switches and detection equipment.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO barrier radar set containing two sensors and one evaluation unit. Configurable fields support presence monitoring and activation zones, with Wi-Fi setup. This configuration handles two sensor positions through one evaluation unit.
Original manufacturer: ASO Safety Solutions.
View the product page →
LISENS radar sensor for contactless detection around a barrier, supplied without an evaluation unit. It joins a compatible LISENS scan system to configure presence and activation fields. This reference is the individual sensor for a defined configuration or system extension.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO tactile bumper for moving systems needing deformation travel and outdoor use. The 100-120 L/O combines an absorbing core and internal sensing element under an artificial leather cover. Its 100 × 120 mm section must be selected against the system’s actual stopping behaviour.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO safety contact bumper intended for collaborative robotics. Its deformable structure contains a sensing element that signals actuation to the evaluation electronics. Shape and integration must suit the exposed zones, robot movement and space required for stopping.
Original manufacturer: ASO Safety Solutions.
View the product page →
Tactile bumper with a foam core, aluminium carrier and NBR rubber cover. It serves machine or moving-system projects requiring contact detection with deformation travel. The black surface can receive yellow stripes according to the selected configuration.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO 14 mm safety mat with a aluminium checker plate surface for monitoring an accessible machine area. Pressure on the surface is detected and processed by suitable evaluation electronics. The ARB cover distinguishes this version from flexible-surface mats.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO 14 mm safety mat with a stainless steel tear plate surface for monitoring an accessible machine area. Pressure on the surface is detected and processed by suitable evaluation electronics. The TBV cover distinguishes this version from flexible-surface mats.
Original manufacturer: ASO Safety Solutions.
View the product page →
ASO 14 mm safety mat with a nubbed surface and integrated moulded ramp. It monitors an accessible machine area by detecting pressure, with suitable evaluation electronics. The ramp belongs to this T version and must be included in the floor footprint.
Original manufacturer: ASO Safety Solutions.
View the product page →Connection, mounting and transmission: select accessories for the documented SENTIR profile, ELMON system and installation conditions.
Official KS 4 PRO W - 65-Set illustration, ASO 2025 catalogue, p. 33.
Termination kit for SENTIR edge 65 safety edges, comprising an 8.2 kΩ resistor plug, lock cap, fixation clips and end cap. It prepares the resistive end of the profile in accordance with the ASO assembly procedure.
ASO reference: 1804-2931
View the product page →
Official KS 4 PRO L - 65-Set family illustration; selected code 1804-2991 has a 2.5 m cable, not shown to scale. ASO 2025 catalogue, p. 33.
Connection kit for SENTIR edge 65 with a plug carrying a 2.5 m cable, lock cap, fixation clips and end cap. This code identifies the 2.5 m cable variant in the ASO table, for preparing the connection to the selected evaluation or transmission device.
ASO reference: 1804-2991
View the product page →
Official AL 11-10 rail illustration, ASO 2025 catalogue, p. 38.
Aluminium mounting profile for SENTIR edge 45, 65, 85 and 115 safety edges. The ASO catalogue lists a standard length of 4 m; the current SENTIR edge 65 ST page also names this rail as an accessory.
ASO reference: 103 213
View the product page →
Official AL 30-10 rail illustration, ASO 2025 catalogue, p. 39.
Aluminium mounting profile, 30 mm wide and 10 mm high, offered in a standard length of 4 m. It accommodates SENTIR edge 45, 65 and 85 safety edges; ASO explicitly lists it as a SENTIR edge 65 ST accessory.
ASO reference: 2004-0110
View the product page →
Official 103 225 connection element illustration for AL 11-10, ASO 2025 catalogue, p. 39.
Mechanical connection element identified by ASO for the AL 11-10 aluminium profile. It complements installation of this rail, which is itself listed for SENTIR edge 65 ST. The catalogue gives a width of 30 mm and a height of 8 mm.
ASO reference: 103 225
View the product page →
Official SMS 2004-0230 illustration for SENTIR edge 45/65/85, ASO 2025 catalogue, p. 41.
ASO Smart Mounting System for the SENTIR edge 45, 65 and 85 families. This mounting accessory has its own 2004-0230 code and complements tactile-profile fixing options; the catalogue lists a 30 × 10 mm section.
ASO reference: 2004-0230
View the product page →
Official SPK 54 S travelling core illustration, code 1317-0010, ASO 2025 catalogue, p. 69.
Travelling inductive coil core for external mounting on the gate and connection of moving safety edges. The S version uses plug-in screw terminals. The ELMON inductive 77 manual identifies code 1317-0010 and describes its role in the transmission loop.
ASO reference: 1317-0010
View the product page →
Official SPK 54 M travelling core illustration, code 1317-0020, ASO 2025 catalogue, p. 69.
Travelling inductive coil core for external mounting on the gate, with safety edges connected through moulded M8 female connectors. This M version has a separate order code from SPK 54 S and is explicitly listed in the series described by the ELMON inductive 77 manual.
ASO reference: 1317-0020
View the product page →
Official SPK 55 stationary core illustration, code 1319-0010, ASO 2025 catalogue, p. 69.
Stationary inductive coil core for external mounting on the gate profile. In the manufacturer’s ELMON inductive 77 example, it connects the inductive loop to the evaluation device opposite the travelling SPK 54 core. Code 1319-0010 is confirmed in the manual.
ASO reference: 1319-0010
View the product page →
Official ISB A4 mechanical kit illustration, code 1209-0020, ASO 2025 catalogue, p. 69; cores and a receiver are not mentioned in the listed contents.
Mechanical set for external installation of an ASO inductive transmission loop. The catalogue lists a clamping unit, mounting brackets, 20 m of steel rope and accessories. Code 1209-0020 identifies this mounting set, distinct from the inductive cores and electronics.
ASO reference: 1209-0020
View the product page →State closure or machine type, contact zones, dimensions and existing control interfaces. Manufacturer instructions and installation conditions determine components and validation of the complete chain.
Discuss your project →Manufacturer documents remain in their original language.
